|
|
Topic: Wheel parts interchangeable?
|
Email this topic to a friend |
Subscribe to this Topic
| Report this Topic to Moderator
|
Page 1 of 1 of 6 replies
|
|
|
November 02, 2013 at
12:34:07 PM
|
|
Joined:
|
11/02/2013
|
Posts:
|
5
|
|
|
Are wheel halves from different manufacturers interchangeable? Will MPD wheel halves fit on Weld Racing 42 spline wheel centers?
|
|
|
November 02, 2013 at
08:25:05 PM
|
|
Joined:
|
12/24/2009
|
Posts:
|
37
|
|
|
Not all wheel parts are interchangeable between different manufacturers but mpd and weld are.
|
|
|
November 02, 2013 at
11:17:26 PM
|
|
Joined:
|
01/22/2012
|
Posts:
|
83
|
|
|
Reply to:
Posted By: rbc on November 02 2013 at 12:34:07 PM
Are wheel halves from different manufacturers interchangeable? Will MPD wheel halves fit on Weld Racing 42 spline wheel centers?
|
centers are all interchangeable but not all beadlock rings are
|
|
|
|
November 09, 2013 at
01:30:41 PM
|
|
Joined:
|
12/04/2005
|
Posts:
|
24
|
|
|
Well, I have some centers with 15 holes and some with 18 holes. Plus the really old ones with 20 holes on a much larger diameter. And I just aquired a Real wheel with 12 holes on a smaller diameter. So I believe you want to at least count the holes.
|
|
|
November 09, 2013 at
02:58:50 PM
|
|
Joined:
|
01/22/2012
|
Posts:
|
83
|
|
|
Reply to:
Posted By: Elliot on November 09 2013 at 01:30:41 PM
Well, I have some centers with 15 holes and some with 18 holes. Plus the really old ones with 20 holes on a much larger diameter. And I just aquired a Real wheel with 12 holes on a smaller diameter. So I believe you want to at least count the holes.
|
forgot about real wheels but between keizer weld and sanders the center pattern is the same
|
|
|
November 09, 2013 at
07:56:48 PM
|
|
Joined:
|
09/02/2009
|
Posts:
|
454
|
|
|
I have some duralights wheels that have an 18 hole pattern.... obviously not interchangeable with the 15 hole wheels....but all the 15 hole wheels are interchangeable for the most part.... weld, sander, kiezer, mpd, along with DMI and winters centers/DM hubs are all the same pattern.
Loose is when you hit the wall with the rear of the
car, tight is when you hit the wall with the front of
the car. Horsepower is how fast you hit the wall and
torque is how far you move the wall.
|
|
|
|
December 18, 2013 at
06:43:49 PM
|
|
Joined:
|
12/04/2005
|
Posts:
|
24
|
|
|
I'm still interested in any interchangability between beadlock rings. Specifically, I have two Weld wheel-halves I want to use, but none of my "miscellaneous spare" rings fit, and they all lack brand names. The rings I have are also 16 bolt, but the bolt circle is a bit larger than Weld's. I scrounge for parts on eBay and at swap meets, and don't mind mixing brands if they fit, so any information on any brands would be helpful. Thanks!
|
|